- March 30, 2022The structure of the tie is complicated , and the " small coil " in it should not be pulled or cut . take from twitter . On important formal occasions , it is often necessary to wear a neat suit and tie . The structure of a tie is actually quite a lot of knowledge , and it is not easy to master it completely . Recently , the Japanese media reminded an important detail that beginners is easy to overlook . According to Japanese media (grape ) reports , the person in charge of a well-known Japanese tie maker (SHAKUNONE ) recently shared with the official Twitter that there is a circled silk thread near the tip of the inner tie . For someone seeing a tie for the first time , it's likely to accidentally cut it , or just out of curiosity , try to pull the thread . However , that coil is actually the tie's " adjustment line " that provides assistance when tying or unwinding the tie , so it's usually best not to touch it . Due to the recent graduation season in Japan , many students will enter the workplace and may only come into contact with ties for the first time , so SHAKUNONE will come forward to remind them to prevent new people in the society from accidentally making mistakes . Netizens also said , " I've always been thinking about " what the hell is this thread doing " while pulling it , so it's not okay " , " I didn't notice it before " , " My husband rarely wears suits , . So I didn't even notice that my son is graduating this year , so it's hard to see a reminder " , " I collected more than 10 ties because they looked good , but I didn't find it " , " I accidentally cut them off before . " , will pay attention later " .
- March 29, 2022Tie make step: 1 . Cutting the tie fabric : The surface fabric needs to be cut into three sections , which are 40 inches in the large end , 10 inches in the middle , 10 inches in the small end ; 55 inches in the inner lining ; 2 small pieces in the silk . 2 . Splicing the tie cloth . Splicing the big end , middle end , and small end fabrics together . Precautions for splicing : The splicing position is a 45degree diagonal line . The stripes on the front of the fabric should look natural and beautiful , and the seam on the back of the fabric should be wider . 3 . Make the tie lapel . The production level of the lapels directly reflects the grade in the tie . Before sewing , the two ends of the tie should be trimmed into right angles and equal sides , symmetrical to the left and right , and then the reverse side of the tie and the reverse side of the silk should be closely attached . After the overlock is finished , turn it over to the front and iron it flat . 4 . Preliminarily iron the tie . Lay the tie face down on the ironing table , place the tie lining in the middle of the tie , fold the edge of the tie inward by 0.5 inches , the fold should be in a straight line , and then fold the sides closer together after ironing , iron again flat , and use a bead needle fixed . 5 . Sew the tie . The centerline behind the sarcasm and the tie . Hand-stitched with topstitching , you can sew straight lines or fork lines , depending on the pattern of the tie and the color of the stitching . 6 . Iron the new tie to make it straight and beautiful , so that the manual tie are finished . Button ties / tied method : 1 . Draw a pattern of a tie , and cut two pieces of cloth facing each other , paying attention to the seam allowance . Sew face-to-face and turn to the front ; 2 . Prepare a small piece of 45-degree twill fabric of the same color , 6.5cm*7cm for the bow tie , and 5cm*20cm for the upper part of the bow tie , all including seam allowances ; 3 . Pinch out the folds from top to bottom of the tie body , about 2cm-2.5cm , and sew it on by…
- March 14, 2022No matter you custom ties for your corporate, university, or workshop, a right supplier can make you more easilier in…
- March 14, 2022Use this list of homeowner favorites to find the color that's right for you. Buy necktie for yourself or friends,…
- March 8, 2022When the wedding is approaching, no matter what kind of dress the groom chooses, don't forget another important detail -…
- March 8, 2022In 2021, our manufacturer have custom designed a new fabric - Luminous Fabric, and we use this fabric to our product now. In 07/06/2021, the first…
- January 22, 2022January is just about the end, what’s the most popular tie of the month? Let’s make an inventory the best…
- January 15, 2022When a customer make an order to us, we should know the detail of the tie. Including size, material, pattern,…
- January 5, 2022In the first week of 2022, I hope you every things goes well. And what's your best look tie of…
- January 4, 2022Firstly. HAPPY NEW YEAR. I hope you all enjoyed the end of year polls, and results. I thought it…